GV-POEX0100

GV-POEX0100 One-Port PoE Extender    10/100 PoE extender  PoE (IEEE 802.3af) and PoE+ (IEEE 802.3at) compliant  Extension up to 600 m (1,968.5 ft) using 5 GV ‐POEX0100  Compatible with GV ‐ IP Cameras  No additional power supply required  Introduction  GV ‐POEX0100 is a single ‐ port, 10/100 PoE extender that can extend the distance between a PoE switch and a GV ‐ IP Camera by 100 m  (328.08 ft) for every extender installed. They can be serially connected, with no additiona...

Garantie: 36 mon.

Datentabelle 

Textinhalt des PDF-Datenblattes:

GV-POEX0100 One-Port PoE Extender

10/100 PoE extender
PoE (IEEE 802.3af) and PoE+ (IEEE 802.3at) compliant
Extension up to 600 m (1,968.5 ft) using 5 GV ‐POEX0100
Compatible with GV ‐ IP Cameras
No additional power supply required
Introduction
GV ‐POEX0100 is a single ‐ port, 10/100 PoE extender that can extend the distance between a PoE switch and a GV ‐ IP Camera by 100 m
(328.08 ft) for every extender installed. They can be serially connected, with no additional power supply, to transmit power and data
to a GV ‐ IP Camera as fa r as up to 600 meters (1,968.5 ft) away from a PoE switch.
Requirements
The maximum distance allowed between a PoE switch and a GV ‐ IP Camera depends on the PoE switch type, PoE power output of the
connected device (PD) and the type of power supply. These can be summarized below.
GV ‐ IP Cameras Powered by PoE

Brand & Model
GeoVision
PD of GV ‐ IP Cameras
GV ‐POE0801 / 0811
GV ‐POE1601 / 1611
GV ‐POE2401 / 2411
GV ‐POE0400
GV ‐POE0800
GV ‐POE0810

Third‐ Party PoE Switches

(IEEE 802.3at)
PD < 6.49 W
(IEEE 802.3af)
600 m (1,968.5 ft) 400 m (1,312.34 ft) 400 m (1,312.34 ft)
PD 6.5 W ~ 12.95 W
(IEEE 802.3af)
400 m (1,312.34 ft) 200 m (656.17 ft) 200 m (656.17 ft)
PD 13 W ~ 25.5 W
(IEEE 802.3at)
200 m (656.17 ft) ‐ ‐
PD > 25.5 W ‐ ‐ ‐
Note:
1. Each GV ‐POEX0100 extends another 100 m (328.08 ft)between the PoE switch and the GV ‐ IP Camera. Therefore, a distance of 200
m requires one GV ‐POEX0100 and 400 m (1,312.34 ft) requires three etc.
2. GV ‐POE0100 can only be connected using CAT ‐ 5e cables, TIA/EIA ‐568 ‐ B, with the maximum DC resistance of 9.38 ohms/100 m.
GV ‐ IP Cameras Powered by PoE
GeoVision
Brand & Model
GV ‐POE0801 / 0811
GV ‐POE1601 / 1611
GV ‐POE2401 / 2411
GV ‐POE0400
GV ‐POE0800
GV ‐POE0810

Third‐ Party PoE Switches

(IEEE 802.3at)
GV ‐ IP Cameras 600 m (1,968.5 ft) 400 m (1,312.34 ft) 400 m (1,312.34 ft)
GV-POEX0100 March 23, 2018
- 1 -


GV-POEX0100 March 23, 2018
- 2 -
Compatibility
1. GV ‐POEX0100 is only compatible with third ‐ party switches that comply to PoE+ (IEEE 802.3at) and is not compatible with
GV ‐PA191/481/482/901.
2. GV ‐POEX0100 supports all GV ‐ IP Cameras when installed with a power adapter and does not support the following models
when powered by PoE:
• GV ‐BX2510 ‐ E / 5310 ‐ E
• GV ‐FE3403 / 5303
• GV ‐VD2540 ‐ E / 5340 ‐ E
• GV ‐SD220 / 220 ‐ S
3. GV ‐POEX0100 is only compatible with the following GeoVision PoE switches of the indicated firmware versions:
• GV ‐POE0801 / 1601 / 2401 (V1.03 or later)
• GV ‐POE0811 / 1611 / 2411 (V1.01 or later)
Specifications
Ports
Network Standard 10/100 Mbps half/full duplex

Connectors RJ ‐ 45

Network cables Cat5e or higher

Mechanical

LED Indicator
4 LEDs: Power x2, Network x2
Power indicator: PoE enable (Amber)
Network indicator: Link (Green), Activity (Green Blink)

PoE Control Button On / Off

General

Operating Temperature ‐10°C ~50°C (14°F ~ 122°F)

Humidity 10% to 90% (no condensation)

Environment Indoor

Dimensions (L x W x H) 102.8 x 28.8 x 20 mm (4.05" x 1.13" x 0.79")

Weight 87 g (0.19 lb)

Regulatory CE, FCC Class A, RoHS compliant

Note: Specifications are subject to change without notice.
Packing List
1. GV ‐POEX0100
2.Screw x 2
3.Screw anchor x 2
4. GV ‐POEX0100 Installation Guide